Weaving and Fabric Structures · 4 min read

Shedding Picking and Beat-Up

Shedding, picking and beat-up are the three primary motions of weaving. This article explains each one in simple words and shows how they repeat to build cloth.

Illustrated cover: warp threads, a raised shed, a gold weft pick and a comb-like beat-up bar building woven cloth, for the article Shedding Picking and Beat-Up.

What are the three primary motions of a loom?

Shedding, picking and beat-up are the three primary motions of weaving. Shedding lifts some warp yarns to open a gap. Picking sends the weft yarn through that gap. Beat-up pushes the new weft yarn firmly against the cloth already woven.

Warp yarns run along the length of the fabric, and weft yarns run across its width. A loom is the machine, or frame, that holds the warp tight so the weft can be interlaced with it. These three motions repeat again and again, and each round adds one weft yarn to the cloth.

They are called primary because weaving cannot happen without them. Other motions, such as letting the warp off its beam and winding the cloth forward, support them and keep the work going.

What is shedding and why does the warp need to open?

Shedding is the motion that separates the warp yarns into two layers, one raised and one lowered. The gap formed between these layers is called the shed. It is the opening through which the weft will travel, much like a tunnel made inside the warp.

Which yarns go up and which stay down decides the weave. In plain weave, the odd warp yarns rise on one pass and the even ones rise on the next. In twill or satin, the lifting order changes, so the crossings form diagonal lines or long floating yarns instead.

On a loom, warp yarns pass through small eyes in frames called heald shafts or harnesses. Lifting a shaft lifts every yarn threaded through it. A weave draft, which is a chart of the lifting plan, tells the weaver which shafts to raise on each pick.

What is picking and how does weft insertion happen?

Picking is the motion that carries the weft yarn across the loom through the open shed. One single passage of weft is called a pick. Weft insertion is another common name for this step, because the weft is inserted between the two warp layers.

On a simple handloom, the weaver throws a shuttle, a boat-shaped holder carrying the weft yarn, from one side to the other. The shuttle slides through the shed and leaves a trail of weft behind it. Powerlooms may use a shuttle too, while other looms send the weft by other means.

Whatever the method, the aim is the same. The weft must travel the full width of the warp, at the right moment, while the shed is open. If the shed closes too early or the weft is not pulled to the right tension, the cloth will show faults such as loose loops or missing picks.

What does beat-up do to the fabric?

Beat-up is the motion that pushes the newly laid weft yarn into its place against the edge of the finished cloth. This edge is called the fell of the cloth. The weft is carried to the fell by a comb-like frame called the reed, which swings forward and back.

The reed also keeps the warp yarns evenly spaced across the width. Its gaps, called dents, hold the warp in order. Each forward swing of the reed packs the weft snugly, and the force of this beat helps decide how close together the picks will lie.

Close beating gives a dense, firm cloth with many picks per inch. Lighter beating gives a more open, softer one. You can read more about counting these in our post on ends and picks per inch.

How do the three motions work together in one cycle?

Think of the cycle as three steps in a fixed order. First the shed opens, then the weft passes through, then the reed beats it into place. After that, the shafts change position to form a new shed, and the cycle begins again with the next pick.

A cloth is simply thousands of these cycles stacked one above another. If the timing is correct, the interlacing is neat and the fabric is even. If one motion is early or late, you may see uneven spacing, loose weft or broken yarns.

When you look at a woven sample, you can try to imagine the motions behind it. Count the weft rows, notice how close they sit, and ask which yarns were lifted for each row. This habit connects what you see in cloth with what happens on the loom.

Take it with you

Key takeaways.

  • Shedding opens the warp, picking sends the weft through the opening, and beat-up presses that weft against the cloth.
  • The order in which warp yarns are lifted during shedding decides whether the weave is plain, twill, satin or another structure.
  • The force of beat-up, together with the reed spacing, affects how dense or open the finished fabric feels.
  • These three motions repeat for every single pick, so even a small piece of cloth holds many cycles of the same simple sequence.